Renewable Energy · Basic level · 3 min read ·
What is a solar panel or photovoltaic module?
A solar panel, or photovoltaic module, is the device that turns sunlight into direct-current electricity. Its size is measured in watt-peak (Wp): the most it delivers under laboratory conditions. Adding up the Wp of every panel gives you a system's peak (DC) power.
In 30 seconds
- It turns light into direct current; the inverter converts it to alternating current.
- Wp is its maximum output in the lab, not what it delivers every hour.
- It loses a little performance each year, which is why it carries a production warranty.
Why should you care?
The panel is the most visible part of a solar project. Knowing what its numbers say helps you read the technical sheet without getting lost.
- You know where a project's peak power comes from and how it differs from its regulatory capacity.
- You tell the panel's power apart from the energy the system produces.
- You see why degradation and warranties matter over a long horizon.
Think of it as a roof tile that harvests light
Think of the panel as a roof tile that, besides covering, collects the light falling on it and turns it into electricity. More tiles and more sun mean a bigger harvest; on a cloudy day the same tile collects less.
How does the solar panel work?
- 1
Light reaches the cells
Each panel has dozens of silicon cells. When light hits them, they free electrons and a current flows.
- 2
Direct current comes out
Panels are wired in groups and deliver direct current (DC), the same kind a battery gives.
- 3
The inverter converts it
The inverter turns that current into alternating current (AC), the kind appliances and the grid use.
- 4
The watt-peaks add up
Peak (DC) power is the number of panels times each one's Wp. For regulatory purposes, installed capacity is the sum of the inverters' rated AC output.
The formula
Peak power (DC) = Number of panels × Wp per panel
- Number of panels
- = modules installed in the system
- Wp
- = watt-peak of each panel, from its datasheet
An example with numbers
A rooftop with 20 panels of 500 Wp in an area with 4.5 peak sun hours a day and a performance ratio (PR) of 0.8, as in the capacity factor lesson. Illustrative figures, unrelated to any project.
| Capacity (20 × 500 Wp) | 10,000 Wp = 10 kWp |
|---|---|
| Energy per day (10 × 4.5 × 0.8) | 36 kWh |
| Energy per year (36 × 365) | 13,140 kWh |
| If one panel gets dirty or damaged | output dips, but the others keep producing |
Wp tells you the size of the system. The energy also depends on the site's sun and on losses, which the 0.8 PR sums up.
Where do you see it at Circular Urban?
Each solar project's sheet details the panels it uses: brand, model and watt-peak per module, next to the system's capacity. These are design figures; real production depends on the weather, maintenance and the project's actual performance.
- Each solar project's sheet, in Technical Specifications: Solar Modules.
- In the same section: DC Capacity and AC Capacity.
What changes in your finances once you get it
You read the datasheet with judgment
You know a panel's Wp describes its size, not what it delivers every hour.
You run a quick estimate
With the capacity and the site's peak sun hours you estimate daily energy: kWp × PSH × 0.8.
You look at the long run
You check annual degradation and warranties, because a panel works for 25 years or more.
Common mistakes
- Myth
A 500 Wp panel delivers 500 watts all day.
- In reality
It only gets close to that in full sun at an ideal temperature. In the morning, the afternoon or under clouds it delivers less.
- Myth
Panels don't work when it's cloudy.
- In reality
They keep producing with diffuse light, just less. What stops them is the night.
- Myth
A panel produces the same throughout its life.
- In reality
It loses a small percentage of performance each year. That's why manufacturers give a long-term production warranty.
Test yourself
A system has 40 panels of 450 Wp. What is its peak power?
Keep learning
Helps to know first
This content is educational. Every participation carries risks inherent to the project, including the possibility of partial or total loss, and results are subject to each project's actual performance.

