Renewable Energy · Basic level · 3 min read ·
What do GW, MW and kWp mean?
GW, MW and kW measure power: the size of a system, not the energy it delivers. 1 GW is 1,000 MW and 1 MW is 1,000 kW. The "p" in kWp stands for peak, the panels' maximum output under ideal conditions. Energy is measured separately, in kWh or MWh.
In 30 seconds
- kW, MW and GW measure size; kWh, MWh and GWh measure energy produced.
- Each step multiplies by 1,000: 1 GW = 1,000 MW = 1,000,000 kW.
- The "p" for peak marks panel capacity under laboratory conditions.
Why should you care?
The news talks in gigawatts and project sheets in kilowatt-peak. If you mix up power and energy, a project can look much bigger or smaller than it is.
- You compare projects of different sizes in the same unit.
- You separate the size of a system from what it produces in a year.
- You understand national targets, such as GW of solar capacity, next to a single project.
Think of it as the width of the tap and the water that flows
Power is like the width of a tap: it says how much water can flow at once. Energy is the water that actually filled the bucket in a day. A wide tap opened briefly fills less than a narrow one left open all day.
How does GW, MW and kWp work?
- 1
Spot the unit
kW, MW or GW is power. If it ends in an "h", kWh or MWh, it's energy.
- 2
Convert between steps
Multiply or divide by 1,000: 2.5 MW is 2,500 kW; 3,000 kW is 3 MW.
- 3
Go from power to energy
Multiply the power by the hours it works at that rate. In solar you use peak sun hours and the performance ratio.
The formula
Energy (kWh) = Power (kWp) × Peak sun hours × PR
- Power (kWp)
- = peak (DC) power of the panels
- Peak sun hours
- = equivalent hours of full sun per day at the site
- PR
- = performance ratio; 0.8 is a common reference
An example with numbers
A 1 MWp project in an area with 4.5 peak sun hours a day and a PR of 0.8. Illustrative figures, unrelated to any project.
| Capacity | 1 MWp = 1,000 kWp |
|---|---|
| Energy per day (1,000 × 4.5 × 0.8) | 3,600 kWh = 3.6 MWh |
| Energy per year (3.6 × 365) | 1,314 MWh |
| Equivalent 5 kWp rooftops | 200 |
1 MWp is the size; 1,314 MWh is what it would produce in a year. They are two different numbers you read together.
Where do you see it at Circular Urban?
On each solar project's sheet, capacity appears in kWp or MWp and production in MWh. With this lesson you can move from one to the other and check that the figures make sense. They are design projections, not assured results.
- Each solar project's sheet, in Technical Specifications: DC Capacity and AC Capacity.
- Each solar project's sheet, in Energy Production: Annual Production.
What changes in your finances once you get it
You don't trip on the unit
Before comparing two figures, you check whether both are power or both are energy.
You put figures in scale
You know a home rooftop is around 5 kWp and that 1 MW is about 200 of those rooftops.
You check consistency
With kWp × 4.5 × 0.8 × 365 you see whether a sheet's annual production sits in a reasonable range.
Common mistakes
- Myth
A 1 MW system produces 1 MW a day.
- In reality
MW is size, not energy. Production is measured in MWh and depends on how many sun hours the site gets.
- Myth
kW and kWh are the same thing written differently.
- In reality
kW is power at an instant; kWh is energy accumulated over time. Your power bill charges kWh.
- Myth
kWp is the power the system always delivers.
- In reality
It's the maximum under ideal conditions. It almost always delivers less, because of the time of day, clouds and temperature.
Test yourself
A 5 kWp rooftop sits in an area with 4.5 peak sun hours and a PR of 0.8. How much energy does it produce per day?
Keep learning
This content is educational. Every participation carries risks inherent to the project, including the possibility of partial or total loss, and results are subject to each project's actual performance.

